Kataloge >
Depuy Synthes >
Sacral Bars

Sacral Bars
16Seiten

Katalogauszüge

Sacral Bars. Fixation of the posterior pelvis in cases of fractures or sacroiliac joint dislocations. Technique Guide

Introduction Sacral Bars 2 Surgical Technique Preoperative Planning 5 Product Information Sacral Bar Sets 11 Synthes Biomaterials Overview 13 This description alone does not provide sufficient background for direct use of the product. Instruction by a surgeon experienced in handling this product is highly recommended Reprocessing, Care and Maintenance of Synthes Instruments For general guidelines, function control and dismantling of multi-part instruments, please refer to: www.synthes.com/reprocessing

Katalog auf Seite 3 öffnen

Sacral Bars. Fixation of the posterior pelvis in cases of fractures or sacroiliac joint dislocations. − Sacral washers prevent the rounded sacral nuts from pressing into the cortical bone − The sacral bars feature a trocar tip for easy passage through the soft tissues − The sacral bars are fully threaded and are available in 200 mm or 260 mm lengths − The implants are not in direct contact with the neurological structures of the Os sacrum which reduces the risk for iatrogenic injuries 2 Synthes Sacral Bars Technique Guide

Katalog auf Seite 4 öffnen

AO Principles In 1958, the AO formulated four basic principles, which have become the guidelines for internal fixation.1, 2 Those principles as applied to the sacral bars are: Anatomic reduction Fixation of sacral fractures and fracture dislocations of the sacroiliac joint with the threaded sacral bars allows the restoration of anatomical relationships. Stable fixation Hexagonal and rounded sacral nuts can be wedged against each other and thus compression can be achieved. The recommended two-bar technique adds stability to the construct. Preservation of blood supply The sacral bars bridge...

Katalog auf Seite 5 öffnen

The Synthes Sacral Bars are indicated for fixation of the pos- terior pelvis, in areas of the posterior superior iliac spine, posterior inferior iliac spine, for sacral fractures, and fracture dislocations of the sacroiliac joint. 4 Synthes Sacral Bars Technique Guide

Katalog auf Seite 6 öffnen

Preoperative Planning 321.200 Ratchet Wrench for Nut, hexagonal, This procedure can be performed manually using a universal chuck with T-handle, or with power equipment. Note: In the case of bilateral fracture, it is necessary to have at least one side of stable reduction using a sacroiliac screw or posterior plate in addition to inserting sacral bars. The correct length of the sacral bar should extend 25-30 mm on either side of the posterior iliac crest (bar will For additionally required instruments, please see page 12.

Katalog auf Seite 7 öffnen

Surgical Technique The patient is placed in the prone position. Make slightly curved bilateral incisions just lateral to the pos- terior superior iliac spine. The incision on the fracture side should be large enough to allow for direct visualization and 6 Synthes Sacral Bars Technique Guide

Katalog auf Seite 8 öffnen

Reduce and stabilize the fracture Reduce the fracture using pointed reduction forceps from the medial sacral crest to the lateral aspect of the posterior superior iliac spine, or from the opposite side using pelvic re- duction forceps. After reduction, two Kirschner wires should be placed across the sacroiliac joint for provisional stabiliza- Drill gliding holes 310.60J Drill Bit 6.0 mm, for Jacobs Chuck, Drill a set of gliding holes using a 6.0 mm drill bit. The holes should be located so that the first bar is placed at the level of L5/S1 interspace as seen on C-arm or by palpation. The...

Katalog auf Seite 9 öffnen

Surgical Technique 5 Insert first sacral bar Instruments 296.763 or 296.766 Threaded Sacral Bar, length 200 mm, Stainless Steel Threaded Sacral Bar, length 260 mm, Stainless Steel Drive the sharp trocar tip of the threaded sacral bar through the predrilled hole in the contralateral iliac spine. The sacral lamina must be seen, to ensure that the bar passes dorsal to it and does not enter the sacral canal; it may pass through the medial sacral crest. 6 Apply washers and rounded nuts Instruments 296.758 Washer л 6.0 mm 296.757 Nut, rounded, л 6.0 mm 321.160 or 321.200 Combination Wrench л 11.0...

Katalog auf Seite 10 öffnen

7 Apply hexagonal nuts Instruments 296.759 Nut, hexagonal, л 6.0 mm 321.160 or 321.200 Combination Wrench л 11.0 mm Ratchet Wrench for Nut, hexagonal, 11.0 mm Add 6.0 mm hexagonal nuts to maintain compression. With a hexagonal wrench, wedge the hexagonal nuts against the rounded sacral nuts. Note: Pay attention not to over-compress the construct. 8 Place second bar Repeat steps 5–7 for insertion and fixation of the second sacral bar. Two bars must be used to avoid rotation. Remove Kirschner wires. Synthes 9

Katalog auf Seite 11 öffnen

Surgical Technique 9 Trim sacral bars Instrument 388.720 Bolt Cutter Use the bolt cutter to cut the ends of the sacral bars flush with the hexagonal nuts. 10 Synthes Sacral Bars Technique Guide

Katalog auf Seite 12 öffnen

Each set contains the necessary sterile implants and drill bit for one surgical procedure as described in the technique Bar Length 200 mm, sterile Bar Length 260 mm, sterile 01.100.763 contains the following implants and instruments: 296.763S* Threaded Sacral Bar, length 200 mm, 0 6.0 mm. Stainless Steel, sterile 2 310.60JS Drill Bit 6.0 mm, for Jacobs Chuck, 01.100.766 contains the following implants and instruments: 296.766S* Threaded Sacral Bar, length 260 mm, 0 6.0 mm. Stainless Steel, sterile 2 310.60JS Drill Bit 6.0 mm, for Jacobs Chuck,

Katalog auf Seite 13 öffnen

Additional Instruments The following instruments are additionally required: Ratchet Wrench for Nut, hexagonal, Bolt Cutter Universal Chuck with T-Handle Also available: 398.860 Pelvic Reduction Forceps, long, with pointed ball tips, speed lock, Oscillating Drill Attachment 12 Synthes Sacral Bars Technique Guide

Katalog auf Seite 14 öffnen

Synthes Biomaterials Overview Synthetic and allogenic bone replacement materials have the advantage of uniform quality, unlimited availability and absence of potential complications at a donor site. Additionally, the application of synthetic and allogenic bone graft substitutes reduces the duration of the surgery. Synthes offers a wide range of synthetic biomaterial products in different application forms and with distinct biological properties: chronOS chronOS Perfusion Concept chronOS Inject Osteoconductive, resorbable, synthetic Enhancing chronOS with biological factors Injectable...

Katalog auf Seite 15 öffnen